An Accepted Solution is available for this post.
slow red blinking SYS light, no access
aprildrake
Newbie
‎01-04-2015 11:45 AM

My network extender, bought and activated 12/31/14, has stopped working. I've rebooted several times. GPS is ok, so appears the WAN. But the Sys light is blinking (slowly). Any ideas?

1 person had this problem.
0 Likes
10 Replies
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
7e18n1
Specialist - Level 3
‎01-04-2015 12:32 PM

Network Extender User Guide, blinking red system LED means abnormal condition. Please describe your internet connection; the type, provider and zip code, advertized speed and measured speed and latency. 

An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
aprildrake
Newbie
‎01-04-2015 03:02 PM

was working just fine till last night. my network is Quest, 1MBS (slow I know but the best I can do in my location).

0 Likes
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
aprildrake
Newbie
‎01-04-2015 03:11 PM

98056, I don't know how to measure latency

0 Likes
An Accepted Solution is available for this post.
Re: Re: slow red blinking SYS light, no access
7e18n1
Specialist - Level 3
‎01-04-2015 04:28 PM

Do you mean Qwest CenturyLink DSL @ 1 mbps or 1,000,000 bits per second?

Do you know how far you are from the telco office?

Do this test: speedtest.net, post the 3 test results ping, down, up.

Do a VoIP test at VisualWare. When done, Click Advanced and post the test stats.

0 Likes
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
Ann154
Community Leader
Community Leader
‎01-04-2015 05:33 PM

If you haven't already, power off the network extender and the Internet modem and your router if you have one. Power back on the modem and wait until those light are the steady normal condition. Power on the next device in the connection chain either the extender or the router whichever is connected directly to the modem. Wait until those lights indicate normal operation. Finally reboot the network extender if you haven't done yet. See if the LED lights return to normal operation mode.

If anything in the connection between the extender and the line to the Internet isn't functioning properly, report back or troubleshoot that issue.

I'm most definitely NOT a VZW employee. If a post answered your question, please mark it as the answer.

0 Likes
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
aprildrake
Newbie
‎01-04-2015 07:25 PM

Thanks! Did all this, still doesn’t function L Any more ideas?

0 Likes
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
Ann154
Community Leader
Community Leader
‎01-04-2015 07:34 PM

The extender was registered on your MyVerizon account online?

I'm most definitely NOT a VZW employee. If a post answered your question, please mark it as the answer.

0 Likes
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
aprildrake
Newbie
‎01-04-2015 08:37 PM

I don't know...it just worked when I plugged it in. Now it doesn't.

April Drake

0 Likes
An Accepted Solution is available for this post.
Re: slow red blinking SYS light, no access
John_Getzke
Champion - Level 1
‎01-05-2015 11:08 AM

Chances are you will have to get your NE replaced under the warranty.  I would contact VZW support and have them run you through your options.  They will send you a new one for a problem like this.

0 Likes