Community Forums - Pantech UML295 & Asus RT-AC68U

moscow741 · ‎11-13-2014

Does anyone have any ideas on how to configure the Pantech UML295 Data Modem to work with the Asus RT-AC68U Router ?

7e18n1 · ‎11-15-2014

Tell us what version firmware the router has? Asus made it about as Plug & Play as they can. I’ll assume when you see the “USB Modem” page during Quick Internet Setup, you click Connect, and the router is waiting for additional information on the Basic Configuration page. Is this correct? Have you studied the router’s System Log for clues?

moscow741 · ‎11-15-2014

THANK YOU FOR YOUR HELP :>) !!!!

Firmware Version : 3.0.0.4.374_379; g9540d57

ASUS Support asked me to change the IP address of the router to; 192.168.3.1

That did nothing. Changed back to 192.168.1.1

I have system log saved as text file. Not sure how to forward it to you

7e18n1 · ‎11-15-2014

Did you buy the router at Wal-Mart and do you still have the box and receipt and has it been less than 90 days since you bought it?

The UML295 is a “modem”, changing the router’s LAN side IP address won’t resolve a routing conflict that a modem with a built-in router, like a Jetpack that uses the same IP address as the router, would cause.

Does the UML295 work when attached to a computer and does it require VZ Access Manager? Does VZAM require information from you like a user ID and
password?

moscow741 · ‎11-15-2014

RT-AC68U was a gift. purchased from an online retailer (not WalMart) less than two weeks ago.

I wanted to replace a Cradlepoint MBR95 which accepts the UML295 just fine !

It is connected as we speak ! I do not use a user ID or password for access to Verizon

Network with the Cradlepoint. It connects every time like a charm ! Since the RT-AC68U

gets such GREAT reviews I thought I would like to try it Have some lag time within the LAN

which I thought might be corrected with the more powerful RT-AC68U

Thank-you again for your help !

7e18n1 · ‎11-15-2014

You’re welcome! Good feedback! Try this: Disconnect everything from the Asus except one Ethernet cable between a computer and a LAN port. Connect the modem to the USB 2.0 port. Reset the router by pressing and holding the reset button for 5 to 10 seconds and release. Wait 2 minutes for reset to complete.

Turn off any wireless connection on the computer. Open a browser, it should figure out to use the Ethernet connection and the router’s Quick Internet Setup page should open. If not, navigate to http://192.168.1.1 to open it. I can’t remember the particulars, but I think you press Go and the next page you setup an Admin password so do that.

The next page should be the USB Modem page – again, Asus has made it Plug & Play, all you should have to do is click Connect! Wait three to five minutes and it should figure it out.

If it still fails, continue with the setup and then save the System Log. You can “Mark (highlight), Copy (CTRL C) & Paste (CTRL V)” the last 25-30 lines of it to a post here or do the same thing with the log file itself. The log file is a TXT file you can open with Notepad, and Mark, Copy & Paste it to a message here.

moscow741 · ‎11-15-2014

Followed your instructions to the letter. Nothing ! Also, shouldn't this router have some type of accurate clock ?

Set the time to EST but it continues to show date and time in December / January. Log file appears as Jan 01. Here is last thirty lines of log file.....Thanks again for all your help !!!

ersion 2.6.36.4brcmarm (defjovi@localhost.localdomain) (gcc version 4.5.3 (Buildroot 2012.02) ) #21 SMP PREEMPT Thu Nov 21 15:05:36 CST 2013

Jan 1 00:00:10 kernel: CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f

Jan 1 00:00:10 kernel: CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

Jan 1 00:00:10 kernel: Machine: Northstar Prototype

Jan 1 00:00:10 kernel: Ignoring unrecognised tag 0x00000000

Jan 1 00:00:10 kernel: Memory policy: ECC disabled, Data cache writealloc

Jan 1 00:00:10 kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60928

Jan 1 00:00:10 kernel: Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit earlyprintk debug

Jan 1 00:00:10 kernel: Memory: 255504k/255504k available, 6640k reserved, 0K highmem

Jan 1 00:00:10 syslog: module ledtrig-usbdev not found in modules.dep

Jan 1 00:00:10 syslog: module leds-usb not found in modules.dep

Jan 1 00:00:10 kernel: Virtual kernel memory layout:

Jan 1 00:00:10 kernel: vector : 0xffff0000 - 0xffff1000 ( 4 kB)

Jan 1 00:00:10 kernel: fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

Jan 1 00:00:10 kernel: DMA : 0xf7e00000 - 0xffe00000 ( 128 MB)

Jan 1 00:00:10 kernel: vmalloc : 0xd8800000 - 0xf0000000 ( 376 MB)

Jan 1 00:00:10 kernel: lowmem : 0xc0000000 - 0xd8000000 ( 384 MB)

Jan 1 00:00:10 kernel: modules : 0xbf000000 - 0xc0000000 ( 16 MB)

Jan 1 00:00:10 kernel: .init : 0xc0008000 - 0xc003d000 ( 212 kB)

Jan 1 00:00:10 kernel: .text : 0xc003d000 - 0xc03ad000 (3520 kB)

Jan 1 00:00:10 kernel: .data : 0xc03c6000 - 0xc03e6380 ( 129 kB)

Jan 1 00:00:10 kernel: External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.

Jan 1 00:00:10 kernel: Mount-cache hash table entries: 512

Jan 1 00:00:10 kernel: CPU1: Booted secondary processor

Jan 1 00:00:10 kernel: Found a AMD NAND flash:

Jan 1 00:00:10 kernel: Total size: 128MB

Jan 1 00:00:10 kernel: Block size: 128KB

Jan 1 00:00:10 kernel: Page Size: 2048B

Jan 1 00:00:10 kernel: OOB Size: 64B

Jan 1 00:00:10 kernel: Sector size: 512B

Jan 1 00:00:10 kernel: Spare size: 16B

Jan 1 00:00:10 kernel: ECC level: 8-bit

Jan 1 00:00:10 kernel: Device ID: 0x 1 0xf1 0x 0 0x1d 0x 1

Jan 1 00:00:10 kernel: bio: create slab <bio-0> at 0

Jan 1 00:00:10 kernel: PCI: no core

Jan 1 00:00:11 kernel: PCI: Fixing up bus 0

Jan 1 00:00:11 kernel: PCI: Fixing up bus 1

Jan 1 00:00:11 kernel: PCI: Fixing up bus 0

Jan 1 00:00:11 kernel: PCI: Fixing up bus 2

Jan 1 00:00:11 syslog: module fat not found in modules.dep

Jan 1 00:00:11 syslog: module vfat not found in modules.dep

Jan 1 00:00:11 kernel: VFS: Disk quotas dquot_6.5.2

Jan 1 00:00:11 kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

Jan 1 00:00:11 kernel: pflash: found no supported devices

Jan 1 00:00:11 kernel: bcmsflash: found no supported devices

Jan 1 00:00:11 kernel: Boot partition size = 524288(0x80000)

Jan 1 00:00:11 kernel: lookup_nflash_rootfs_offset: offset = 0x200000

Jan 1 00:00:11 kernel: nflash: squash filesystem with lzma found at block 28

Jan 1 00:00:11 kernel: Creating 4 MTD partitions on "nflash":

Jan 1 00:00:11 kernel: 0x000000000000-0x000000080000 : "boot"

Jan 1 00:00:11 kernel: 0x000000080000-0x000000200000 : "nvram"

Jan 1 00:00:11 kernel: 0x000000200000-0x000002000000 : "linux"

Jan 1 00:00:11 kernel: 0x00000039f87c-0x000002000000 : "rootfs"

Jan 1 00:00:11 kernel: === PPTP init ===

Jan 1 00:00:11 kernel: Registering the dns_resolver key type

Jan 1 00:00:11 kernel: Spare area=64 eccbytes 56, ecc bytes located at:

Jan 1 00:00:11 kernel: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Jan 1 00:00:11 kernel: Available 7 bytes at (off,len):

Jan 1 00:00:11 kernel: (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)

Jan 1 00:00:11 kernel: Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,

Jan 1 00:00:11 kernel: Creating 1 MTD partitions on "brcmnand":

Jan 1 00:00:11 kernel: 0x000002000000-0x000008000000 : "brcmnand"

Jan 1 00:00:11 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:3.

Jan 1 00:00:11 kernel: ctf: module license 'Proprietary' taints kernel.

Jan 1 00:00:11 kernel: Disabling lock debugging due to kernel taint

Jan 1 00:00:11 kernel: et_module_init: passivemode set to 0x0

Jan 1 00:00:11 kernel: et_module_init: txworkq set to 0x1

Jan 1 00:00:11 kernel: et_module_init: et_txq_thresh set to 0x400

Jan 1 00:00:11 kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.34 (r415984)

Jan 1 00:00:11 kernel: wl_module_init: passivemode set to 0x0

Jan 1 00:00:11 kernel: wl_module_init: txworkq set to 0x1

Jan 1 00:00:11 kernel: eth1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.34 (r415984)

Jan 1 00:00:11 kernel: eth2: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.34 (r415984)

Jan 1 00:00:11 kernel: SCSI subsystem initialized

Jan 1 00:00:11 kernel: jnl: driver (lke_8.9.0, Nov 21 2013 15:14:38, LBD=ON) loaded at bf5d3000

Jan 1 00:00:11 kernel: ufsd: driver (lke_8.9.0 lke_8.9.0_r216329_b2, LBD=ON, delalloc, acl, ioctl, ugm, sd, wb) loaded at bf5e0000

Jan 1 00:00:11 kernel: NTFS support included

Jan 1 00:00:11 kernel: Hfs+/HfsJ support included

Jan 1 00:00:11 kernel: optimized: speed

Jan 1 00:00:11 kernel: Build_for__Asus_RT-AC56U_k2.6.36_2013-11-07_lke_8.9.0_r216329_b2

Jan 1 00:00:12 syslog: module proxyarp not found in modules.dep

Jan 1 00:00:12 stop_nat_rules: apply the redirect_rules!

Jan 1 00:00:12 WAN Connection: Ethernet link down.

Jan 1 00:00:12 rc_service: wanduck 496:notify_rc restart_wan_if 0

Jan 1 00:00:13 kernel: scsi 0:0:0:0: CD-ROM PANTECH CD-ROM 0000 PQ: 0 ANSI: 2

Jan 1 00:00:13 kernel: scsi 0:0:0:0: Attached scsi generic sg0 type 5

Jan 1 00:00:14 RT-AC68U: start httpd

Jan 1 00:00:15 kernel: cdc_acm 1-2:1.4: This device cannot do calls on its own. It is not a modem.

Jan 1 00:00:15 kernel: cdc_acm 1-2:1.6: This device cannot do calls on its own. It is not a modem.

Jan 1 00:00:16 disk monitor: be idle

Jan 1 00:00:16 miniupnpd[590]: HTTP listening on port 37564

Jan 1 00:00:16 miniupnpd[590]: Listening for NAT-PMP traffic on port 5351

Jan 1 00:00:16 pppd[591]: pppd 2.4.5 started by admin, uid 0

Jan 1 00:00:16 kernel: hub 1-0:1.0: over-current change on port 1

Jan 1 00:00:16 rc_service: asus_usb_interf 626:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 rc_service: asus_usb_interf 628:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 rc_service: asus_usb_interf 623:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 rc_service: asus_usb_interf 627:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 rc_service: asus_usb_interf 631:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 kernel: hub 1-0:1.0: over-current change on port 2

Jan 1 00:00:16 kernel: tty_port_close_start: count = -1

Jan 1 00:00:16 rc_service: asus_usb_interf 629:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 pppd[591]: Connect script failed

Jan 1 00:00:16 rc_service: asus_usb_interf 625:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:16 rc_service: asus_usb_interf 630:notify_rc reboot

Jan 1 00:00:16 rc_service: waitting "restart_wan_if 0" via wanduck ...

Jan 1 00:00:17 kernel: hub 1-0:1.0: over-current change on port 1

Jan 1 00:00:17 stop_wan(): perform DHCP release

Jan 1 00:00:17 kernel: hub 1-0:1.0: over-current change on port 2

Jan 1 00:00:20 stop_wan(): perform DHCP release

Jan 1 00:00:20 rc_service: wanduck 496:notify_rc restart_wan_if 1

Jan 1 00:00:20 rc_service: waitting "reboot" via ...

Jan 1 00:00:20 FTP Server: daemon is stoped

Jan 1 00:00:21 Samba Server: smb daemon is stoped

Jan 1 00:00:21 kernel: gro disabled

Jan 1 00:00:22 Timemachine: daemon is stoped

Jan 1 00:00:22 WEBDAV Server: daemon is stoped

Jan 1 00:00:10 syslogd started: BusyBox v1.17.4

Jan 1 00:00:10 kernel: klogd started: BusyBox v1.17.4 (2013-11-21 14:59:26 CST)

Jan 1 00:00:10 kernel: Linux version 2.6.36.4brcmarm (defjovi@localhost.localdomain) (gcc version 4.5.3 (Buildroot 2012.02) ) #21 SMP PREEMPT Thu Nov 21 15:05:36 CST 2013