Child Item

Site Totals

61427 Questions Answered 270 Categories

Need help Setting up Multiple Static Ip , 1 for each port of the fios router

Need help Setting up multiple Static Ip on my fios router

I have been trying to figure out how to set up multiple ip in my fios router.
However I kind of managed how to set up multiple static ip However the way I want it is for each port of my router to have an external ip signed to it. ( like 4 different modem in 1 )

Verizon gave me 5 static ip but they can not help me how to set it up.
Have anyone here done more then one static ip on different ports? I assume that the process will be the after the second static ip.

Comments

viafax999

@eltremendo wrote:
Need help Setting up multiple Static Ip on my fios router
I have been trying to figure out how to set up multiple ip in my fios router.
However I kind of managed how to set up multiple static ip However the way I want it is for each port of my router to have an external ip signed to it. ( like 4 different modem in 1 )

Verizon gave me 5 static ip but they can not help me how to set it up.
Have anyone here done more then one static ip on different ports? I assume that the process will be the after the second static ip.

You have a business line?

Are you Fios or dsl? - If dsl the then the config manual is http://www.verizon.com/NROneRetail/NR/rdonlyres/279671B0-05A7-4B4A-9061-4665684E401B/0/LN7500com7FINAL.pdf

What kind of router did they give you?

Not actually sure what pupose the router will have unless you have TV service too.

I would have thought they would have given you documentation on how to do it.

The only way I can think you could do it with a normal fios router is to procure a 5 port switch and connect that to the ont - that will mean that the ont needs to be configured for ethernet connectivity to the premise equipment.

You can then connect 5 different static addressed devices to the incoming fios line.

If you have TV service too one of those devices would have to be the fios router they gave you which should have the default configuration for a fios router except that broadband moca should be disabled and brroadband eth enabled

eltremendo

Thanks for the replay , i actually tried that guide but i do not have DSL so i do not get to do the VCs steps.
my fios router is MI424WR-GEN3I

im looking for any one who have step up multiple static ip on different port using this router ..

By the way i do not have Tv service with this router. i have a second MI424WR-GEN3I router that provides the tv.

viafax999

@eltremendo wrote:
Thanks for the replay , i actually tried that guide but i do not have DSL so i do not get to do the VCs steps.
my fios router is MI424WR-GEN3I

im looking for any one who have step up multiple static ip on different port using this router ..

By the way i do not have Tv service with this router. i have a second MI424WR-GEN3I router that provides the tv.

Im not sure it's possible to do what you want to do with the Actiontec router but can't tell you for sure as I don't have such a router. I know for sure I've never found a way to do it with my FIOS router.

However as I stated before using a switch connected to the ONT will give you 5 WAN ports that you should be able to have your 5 static IP addresses assigned to the devices connected to them.

The alternative might be to put the Actiontec into router mode rather than gateway mode, don't know if that's possible either. Possibly someone with such a router might be able to chime in?? though from the deadly silence I suspect nobody has done it. The real issue is that you need a REAL router rather than a SOHO.

You may want to read this thread as it refers to somebody having done it albeit by connecting a sonicwall device with to a LAN port on the actiontec and then putting that IP address into the DMZ of the actiontec. I guess that would give you 4 static WAN IP addresses firewalled by the sonicwall and one static WAN nat'td IP address via the Actiontec.

http://forums.anandtech.com/showthread.php?t=2309913

Edit.

At post 7 in the thread the poster apparently worked out that he had to put the actiontec into bridged mode to get the un nat'd wan address to the sonicwall which could then use the other wan addresses.

eltremendo

thanks for the help. for instance i set up a wan to have a static ip address undelying the ethernet/coax but i get confused on what type of ip distribution to use. i have 3 options dchp server ( disable , server, relay ) . i changed from time warner and their router was providing me a static ip on each different ethernet port , not sure how they did it.

Child Item